Just How to Remove as Well as Replace a Bath Tub
Just How to Remove as Well as Replace a Bath Tub
Blog Article
What are your thoughts and feelings about Tools You Need to Install a New Bathtub ?
Setting up a tub isn't exactly brain surgery, however it does need strong plumbing, carpentry, and occasionally, tiling skills. Replacing an old bathtub with a brand-new one is additionally a reasonably challenging project. If the old bathtub is conveniently obtainable, the task can relocate immediately; if you have to open a wall to get rid of the old bathtub and also place the brand-new tub, the task is much harder. In either instance, the job is within a house handyman's skills, although you will certainly need an assistant to vacate the old bathtub as well as set in the brand-new one. Make certain you have certified on your own for the task and also fit attempting it. As opposed to employing a contractor to take control of a halfway-completed job, it is far better to think about employing one prior to you begin. Opportunities are you might need a professional plumber to make tube links.
This post will assist you install a brand-new tub in your bathroom if you have actually already bought a brand-new tub and do not need to change the plan of your previous supply of water pipelines.
Your tools and product checklist need to comprise the following:
Preparing for the Setup
Firstly, the sustaining frame provided with the bath must be fitted (if called for) according to the manufacturer's instructions. Next off, fit the faucets or mixer to the tub. When suitable the tap block, it is very important to make sure that if the tap features a plastic washer, it is fitted between the bathroom and the faucets. On a plastic bathroom, it is also reasonable to fit a sustaining plate under the taps system to stop strain on the tub.
Fit the adaptable faucet ports to the bottom of both taps utilizing 2 nuts and olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet through the hole in the bath. Make use of the nut supplied by the maker to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bath. Ensure you make use of all of the supplied washing machines.
Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom need to now prepare to be suited its last position.
Removing Old Taps
If you require to change old faucets with new ones as a part of your installation, then the first thing you must do is separate the supply of water. After doing so, switch on the faucets to drain any water remaining in the system. The process of eliminating the existing taps can be quite troublesome due to the limited access that is typically the situation.
Utilize a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipes to the taps. Have a fabric all set for the staying water that will certainly originate from the pipes. As soon as the supply pipes have actually been removed, utilize the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary taps from turning throughout this procedure. Once the taps have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleansed of any old sealing compound.
Before proceeding to fit the new faucets, contrast the pipeline links on the old faucets to the new taps. If the old taps are longer than the new taps, after that a shank adapter is needed for the brand-new faucets to fit.
Setting up the Bath tub
Utilizing both wood boards under its feet, position the bath tub in the called for position. The wooden boards are useful in evenly spreading the weight of the tub over the area of the boards rather than concentrating all the weight onto 4 little factors.
The following objective is to make sure that the bath tub is leveled all round. This can be attained by examining the level as well as changing the feet on the tub up until the spirit level checks out level.
To install faucets, fit all-time low of the outermost versatile tap connector to the appropriate supply pipeline by making a compression sign up with; then do the very same for the various other tap.
Switch on the water supply and also examine all joints as well as new pipework for leakages and also tighten them if needed. Fill up the tub and additionally inspect the overflow outlet and the regular outlet for leakages.
Finally, repair the bath paneling as explained in the maker's instruction manual. Tiling and also sealing around the bath tub ought to wait up until the bath tub has actually been used at the very least once as this will certainly settle it into its last setting.
Fitting New Touches
If the tails of the new taps are plastic, then you will certainly require a plastic adapter to avoid damages to the string. One end of the port fits on the plastic tail of the faucet as well as the other end offers a connection to the existent supply pipes.
If you require to fit a monobloc, then you will call for minimizing couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next, place the faucet in the mounting opening in the bath/basin making sure that the washers remain in location between the faucet as well as the sink. Secure the faucet in place with the supplier offered backnut. As soon as the tap is securely in position, the supply pipes can be attached to the tails of the taps. The taps can either be linked by using corrugated copper piping or with regular tap adapters. The former type must be connected to the faucet ends initially, tightening just by hand. The supply pipes can later on be linked to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Bathtub
In the area where the bath meets the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is important as the installation can move sufficient to crack an inflexible seal, causing the water to pass through the wall between the bathroom and also the tiling, bring about complications with moisture and also possible leakages to the ceiling listed below.
You can select from a selection of coloured sealants to assimilate your fixtures as well as installations. They are marketed in tubes and cartridges, as well as can sealing gaps as much as a size of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with spins of soaked newspaper or soft rope. Keep in mind to constantly load the bathtub with water before securing, to enable the activity experienced when the bathtub is in use. The sealant can split rather very early if you do not consider this motion prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are additionally conveniently readily available on the marketplace. It is advisable to fit the tiles using water-resistant or water resistant sticky as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I have been very serious about A Step-by-Step Guide to Installing a Bathtub and I hope you enjoyed the new piece. In case you appreciated our blog posting please make sure you remember to pass it around. Thank you so much for going through it.
Schedule And Pricing
Report this page